World-Class Engineered Thermoplastic Valves

Valves

Diaphragm Valves

True Union Type (1/2" - 2")

  • Solid thermoplastic body and bonnet for best overall corrosion resistance.
  • Extra heavy EPDM diaphragm or optional PTFE diaphragm fully backed by EPDM, for long service life under the most severe conditions.
  • Fully lubricated brass stem and sleeve.
  • Unique concave/convex PTFE/ EPDM diaphragm design insures PTFE barrier returns to full open position.
  • Standard, adjustable full close position over travel stop to eliminate premature diaphragm failure due to over tightening.
  • Full stroke, fully protected open/close position indication.
  • Stainless steel or plastic encapsulated external hardware.
  • Longer service life and higher Cv values than rubber lined valves.
  • Can be used in lined, metal FRP or thermoplastic piping systems.
  • Flanged application valves designed to fit between ANSI B16.5 Class 150.
Diaphragm Valves Diagram

Materials of Construction

ITEM PARTS PCS MATERIALS
1 Shaft 1 Brass,PVDF
2 Diaphragm 1 EPDM,TEFLON®
3 Body 1 PVC,PP,CPVC,PVDF
4 Sleeve 1 Brass/PVDF
5 Union Nut 2 PVC,PP,CPVC,PVDF
6 Handle 1 ABS/PPO(Poly Phlnylene Oxide)
7 End Connector 2 PVC,PP,CPVC,PVDF
8 Bonnet 1 PPO(Poly Phlnylene Oxide)
9 Gauge Cover 1 PC
10 O-Ring 2 EPDM,VITON®
11 Compressor 1 PVDF/Brass/PPO
12 Indicator 1 PE
13 Bolt 4 SUS304
14 Nut 4 SUS304
15 Washer 4 SUS304

VITON® is a trademark of DuPont Performance Elastomers
TEFLON® is a trademark of DuPont Performance Elastomers

Note: For valves to be used in sodium hypochlorite, factory must be consulted for alternate gasket material

Ansi Dimensions

Size Inch d P B L H A F K Test Pressure (PSI)
Socket Thread TFE Diaphragm Rubber Diaphragm
1/2" 0.840 NPT1/2" 0.875 2.126 6.457 4.094 3.189 0.984 M6 104 150
3/4" 1.050 NPT3/4" 1.00 2.126 6.457 4.094 3.189 0.984 M6 105 150
1" 1.315 NPT1" 1.125 2.480 7.087 4.567 3.583 0.984 M6 104 150
1 1/4" 1.660 NPT1 1/4" 1.250 3.346 9.252 5.591 4.606 1.772 M8 104 150
1 1/2" 1.900 NPT1 1/2" 1.375 3.346 9.252 5.591 4.606 1.772 M8 104 150
2" 2.375 NPT2" 1.500 3.898 10.472 6.929 5.906 1.772 M8 104 150

TestingProcedure: Every valve is tested for bubble tight shutoff prior to leaving the factory.
Pressure testing performed on PVC/EPDM valves at 73°F water temperature, non-shock.

True Union Type Diaphragm Valves (1/2" - 2" SOC./THD./FLANGED)

Design Specifications

Thermoplastic Diaphragm Valves 1/2" - 2" Soc./ Thd., Flg. (valves shall be molded of solid thermoplastic materials). Body is of the weir configuration exhibiting large flow area and good flow control capability. Stem and sleeve shall be Brass. Full stroke position indication is enclosed in a clear protective cover. All external fasteners shall be either encapsulated in plastic or of stainless steel materials. Materials of construction shall be: (select as required for service)

Body

PVC,CPVC,ASTM D-1784,PP,PPG,ASTM D-4101,PVDF, ASTM D-3222

Bonnet

PVC,CPVC,ASTM D-1784,PP,PPG,ASTM D-4101,PVDF, ASTM D-3222
PPO, ASTM D-4101 (standard)

Stem/Sleeve

Brass

Compressor

PVDF, ASTM, D-3222
PPO, ASTM, D-4101

Diaphragm

EPDM, Ethylene Propylene Diene Monomer
PTFE/EDPM, Teflon® (DuPont Dow Elastomers)

Diaphragm Insert Stud

Stainless Steel, Large Diameter

Positive Indicator Cover

PC, Polycarbonate, ASTM - D-2848

Handwheel

ABS, ASTM D-1788

NOTE: For any diaphragm application with use of sodium hypochlorite, factory must be informed prior to quote. Special application valves are required.

Not recommended for compressed air or gas service.